Stainless steel clamps
Note, note active in product manager:
Walraven SSt HD Clamps Lined M12 – M16
Walraven Bifix® 1301 Clamps SSt Lined M8 M10 (not separate)
Walraven Stainless Steel Pipe Clamp with Lining (M8/10) (not active for INT)
Walraven Clamp with Lining for Spiral Ducts (M8) (not active for INT)
Walraven Stainless Steel Heavy Duty Clamp (M12, M16)
Walraven HD Sprinkler SSt Clamp
Walraven Standard Sprinkler SSt Clamp
Walraven Stainless Steel Pipe Clamp (M8/10) (not active for INT)
Walraven Stainless Steel U-Clamp (not active for INT)
BIS Bifix® 1301 Stainless Steel (M8, M10)
- two-screw clamp
- with quick locking system
- material: stainless steel 1.4404 (AISI 316L)
BIS Bifix® 1301 Stainless Steel (M8, M10)
- two-screw clamp
- with quick locking system
- material: stainless steel 1.4404 (AISI 316L)
BIS Bifix® 300 Stainless Steel (M8, M10)
- two-screw clamp
- with quick locking system
- material: stainless steel 1.4404 (AISI 316L)
BIS Bifix® 300 Stainless Steel (M8, M10)
- two-screw clamp
- with quick locking system
- material: stainless steel 1.4404 (AISI 316L)
BIS 434 Stainless Steel Clamp
- two-screw clamp
- for rigid fixing point fastening it is necessary to use metal clamp liners (Part No. 4337XXX)
- screws secured with anti-loss washer
BIS Bifix® 415 Stainless Steel
- two-screw clamp
- with quick locking system
- removable spacer washers allow the sliding or gripping of the pipe within the clamp
Stainless Steel Rail systems
Stainless Steel Light Rail System
Walraven RapidRail® Stainless Steel Fixing Rail
- C-profile
- for a quick and easy fixing
- with continuous perforation
Walraven RapidRail® Stainless Steel Cantilever Arm
- wall plate with welded C-profile
- slots at 90° to each other to simplify fixing
- CO
2 welded
Walraven RapidRail® Stainless Steel Wall Plate
- flexible base plate for rails
- for fixing to wall, floor or ceiling
- rail can be fixed with slot downwards or sideways
Walraven RapidRail® Stainless Steel Linear Connector
- connector with pre-assembled BIS RapidRail® Slide nut(s)
- to make rail fabrications
- suitable for rail 30x15, 30x20, 30x30
BIS Stainless Steel Rail Prop
- 45° support bracket
- for fixing support under, top or on side of a cantilever arm
- also used to strengthen rail constructions
BIS Stainless Steel Rail Connector
- to make rail fabrications
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Rail Connector
- to make rail fabrications
- material: stainless steel 1.4401 (AISI 316)
Walraven RapidRail® Stainless Steel Beam Clamp
- for a solid fixing to steel construction without the need for welding or drilling
- always use 2 beam clamps per fixing
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Washer (U-shaped)
- U-shaped washer
- U-shaped for extra stability
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Washer (Flat)
- flat washer
- material: stainless steel 1.4401 (AISI 316)
Walraven RapidRail® Stainless Steel Slide Nut
- slide nut with washer and BIS RapidRail® spring
- ready-to-use pre-assembled for a quick fixing, and retains assembly in place before final tightening
- material: metal parts made of stainless steel 1.4401 (AISI 316); spring(s) made of POM (polyoxymethylene), blue
Walraven RapidRail® Stainless Steel Hammerfix
- slide nut with stud bolt, washer and BIS RapidRail® spring
- ready-to-use pre-assembled for a quick fixing, and retains assembly in place before final tightening
- material: metal parts made of stainless steel 1.4401 (AISI 316); spring(s) made of POM (polyoxymethylene), blue
BIS Stainless Steel Slide Nut
- because of shape the nut fits in rail
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Fixpoint Console FPC ‘Medium’
- flexible use console module for high forces (depending on the situation, detailed design by technical service)
- can be used as a pipe connection point in conjunction with 2 or 3 heavy-duty clamps type Stainless Steel Heavy Duty Clamps and Stainless Steel Heavy Duty Clamps with Lining
- tightening torque 75 Nm for the console fixing screws
BIS dB-FiX® 40 Noise Insulating Fixing Point
- noise insulating single fixing point
- material: stainless steel 1.4301 (AISI 304)
- noise insulation by moulded TPE rubber
Stainless Steel Medium Rail System
Walraven RapidStrut® Stainless Steel Fixing Rail
- universal rail system
- distance between rail end and first hole is always equal
- a continuous graduated centimetre scale on one side
Walraven RapidStrut® Stainless Steel Fixing Rail Double
- universal rail system
- distance between rail end and first hole is always equal
- a continuous graduated centimetre scale on one side
Walraven RapidStrut® Stainless Steel Cantilever Arm
- wall plate welded on Strut Profile
- slots at 90° to each other to simplify fixing
- CO
2 welded
Walraven RapidStrut® Stainless Steel Base Plate G2
- flexible base plate for Strut rails
- suitable for all Strut rail up to 82mm height
- open side of rails 41x41 can be turned to all sides
BIS Strut Stainless Steel U-Connector
- U-shaped for extra stability
- longitudinal connector for all Strut rails
- for strong connections and in combination with Double Strut rails it is advised to use linear connectors on both sides of the rail
BIS Strut Stainless Steel Beam Clamp
- for a solid fixing under flanges without welding or drilling
- always use 2 beam clamps per fixing
- material: stainless steel 1.4401/1.4404 (A4) - EN 10088, AISI 316/316L
BIS Strut Stainless Steel Cross Connector
- connector to make cross connections between Strut rails
- to connect Strut rails to wall or ceiling
- the hole pattern is adapted to the hole pattern of Strut rails to use throughbolts
BIS Strut Stainless Steel T-Connector
- T-connector for Strut rails
- the hole pattern is adapted to the hole pattern of Strut rails to use throughbolts
- user friendly by rounded edges
BIS Strut Stainless Steel Z-Connector
- to connect Strut rails to wall or ceiling
- connector to make Z-connections between Strut rails
- can also be used to hang threaded rods from the ceiling with the possibility to adjust the height even after the pipe clamp / pipe is installed
BIS Strut Stainless Steel Connector 90° Rigid
- reinforced connector to make rigid fabrications with Strut rails
- easy fitting due to rounded edges
- material: stainless steel 1.4404 (A4) - EN 10088, AISI 316L
BIS Strut Stainless Steel Angle Connector 90°
- angle connector for all Strut rails to make fabrications
- the hole pattern is adapted to the hole pattern of Strut rails to use throughbolts
- user friendly by rounded edges
BIS Strut Stainless Steel Angle Connector 135°
- angle connector for all Strut rails to make fabrications
- the hole pattern is adapted to the hole pattern of Strut rails to use throughbolts
- user friendly by rounded edges
Walraven RapidStrut® Stainless Steel Slide Nut G2
- slide nut with washer and BIS RapidStrut® spring
- to connect pipe clamps to rails by using threaded rods
- ready-to-use pre-assembled for a quick fixing, and retains assembly in place before final tightening
Walraven RapidStrut® Stainless Steel Slide Nut with Tabs
- slide nut with plastic 'tabs'
- for all types of Strut Rail
- for tight fixing of accessories (e.g. connectors) on rail
BIS Strut Stainless Steel Tee-Bolt
- slide nut with stud bolt and washer
- material: stainless steel
- M10 and M12 tested for fire safety according to EN 1363-1
BIS Stainless Steel Slide Nut
- because of shape the nut fits in rail
- material: stainless steel 1.4401 (AISI 316)
BIS Strut Stainless Steel Washer (U-shaped)
- U-shaped washer
- U-shaped for extra stability
- material: stainless steel 1.4404 (AISI 316L)
BIS Strut Stainless Steel Washer (Flat)
- flat washer
- material: stainless steel 1.4401 (AISI 316)
Stainless Steel fasteners
Note: Walraven Stainless Steel Stud Bolt (only ES)
BIS Stainless Steel Wall Plate Resistance Welded
- slots at 90° to each other to simplify fixing
- Part No. 6717010: CO
2 welded - Part No. 670 7 0XX: material: stainless steel 1.4301 (AISI 304)
BIS Stainless Steel Wall Plate with Welded Stud Bolt 672
- fixings to ceiling or floor (only tension loads recommended)
- slots at 90° to each other to simplify fixing
- with resistance welded male stud bolt
BIS Stainless Steel Hanger Bolt
- material: stainless steel 1.4301 (AISI 304)
BIS Stainless Steel Threaded Rod
- according to DIN 976-1
- material: stainless steel
BIS Stainless Steel Wall Plate with Welded Stud Bolt 672
- fixings to ceiling or floor (only tension loads recommended)
- slots at 90° to each other to simplify fixing
- with resistance welded male stud bolt
BIS Stainless Steel Stud Connector
- to connect 2 male threaded components
- material: stainless steel 1.4301 (AISI 304)
BIS Stainless Steel Thread Adaptor
- to enlarge or reduce the thread size in the connection of clamps, etc.
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Roofing Sheet Hanger
- for mounting to profiled roofing sheet by means of pop rivets or threaded rod
- for applications in environments requiring increased corrosion resistance
- variable distance to roof hanger by using a threaded rod
BIS Toggle Plug (Stud-end)
- U-profile with rotating shaft with stud bolt
- for fixing in hollow walls and hollow ceilings or profiled roofing sheets
- Part No. 0670604: for fixing of sprinkler pipes to roofing sheets (max. DN 50 - 2") according to VdS directives
BIS Toilet Fixing Kit
- Part No. 0657070 is supplied only with white caps
- consists of:
BIS Stainless Steel Hexagon Head Screw
- material: stainless steel 1.4401 (AISI 316)
BIS Stainless Steel Hexagon Nut
- material: stainless steel 1.4401 (AISI 316)
- M10 and M12 tested for fire safety according to EN 1363-1
BIS Stainless Steel Suspension Band
- flexible system with multiple applications
- dispenser cassette allows easy handling and storage
- material: stainless steel 1.4401 (AISI 316)
WTB1 Throughbolt Anchor SSt
- high load capacity
- pre- and through-fixing
- made of stainless steel for use in external atmospheric environment
WDI1 Drop-in Anchor SSt
- simple and quick installation procedure
- medium load capacity
- made of stainless steel for use in external atmospheric environment
BIS HK
- for fixing of steel wire, suspension band or chain in concrete and solid stone
- for suspension of static loads such as air ducts, lowered ceilings, etc. to concrete
- also suitable for outside use
Or visit our international website.